Yes. Set Pr.79 = 3. (Input the start signal from an external source.)

Ensure that the inverter is in the PU operation mode and stopped, change the following parameters: 1. Read Pr.923 (Built

Your suggested use is not recommended due to the following reasons: Output voltage of the 400 V inverter contains "micro

When using one-rank-higher inverter, as you mention, you need to care about the setting of the electronic thermal O/L re

The FM output is 0 to 8 VDC pulse.

The output torque characteristics of the FREQROL-E500 series are shown in the figure below. Figure 1

The RX7 output signal is the same as the signals for NO, NC, and transfer contact output.You can change the contents of

Since a large load is applied to the motor when the electromagnetic clutch turns on, overcurrent may occur if the load i

The internal processing speed is not published. The analog input specifications are as follows: FR-A500???1/4000FR-E500?

To connect the operation panel to the enclosure, use the parameter unit connection cable FR-CB201, FR-CB203, or FR-CB205

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E500

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E500 ]

61-70 of Total 85

prev 7 / 9page next

Using built-in potentiometer and multi-speed together

Yes. Set Pr.79 = 3. (Input the start signal from an external source.) More Details >>
- No：21950
- Release Date：2018/08/22 16:30
Frequency setting

Ensure that the inverter is in the PU operation mode and stopped, change the following parameters: 1. Read Pr.923 (Built-in frequency setting potentiometer g... More Details >>
- No：21416
- Release Date：2018/08/22 16:27
Driving 200 V motor by 400 V inverter

Your suggested use is not recommended due to the following reasons: Output voltage of the 400 V inverter contains "micro surge". Usually this surge voltage i... More Details >>
- No：21403
- Release Date：2018/08/22 16:27
Notes when inverter capacity is larger than motor capacity

When using one-rank-higher inverter, as you mention, you need to care about the setting of the electronic thermal O/L relay.Setting the electronic thermal O/... More Details >>
- No：22040
- Release Date：2018/08/22 16:30
Analog output

The FM output is 0 to 8 VDC pulse. More Details >>
- No：22039
- Release Date：2018/08/22 16:30
Relationship between frequency and output torque

The output torque characteristics of the FREQROL-E500 series are shown in the figure below. Figure 1 More Details >>
- No：22024
- Release Date：2018/08/22 16:30
Alarm output signal when using CC-Link

The RX7 output signal is the same as the signals for NO, NC, and transfer contact output.You can change the contents of this output signal using Pr.192.Pr.19... More Details >>
- No：22008
- Release Date：2018/08/22 16:30
Clutch connection of load

Since a large load is applied to the motor when the electromagnetic clutch turns on, overcurrent may occur if the load is heavy. To ensure that the rated cur... More Details >>
- No：21955
- Release Date：2018/08/22 16:30
Analog signal resolution

The internal processing speed is not published. The analog input specifications are as follows: FR-A500???1/4000FR-E500???1/1000MR-H???1/4000 More Details >>
- No：21550
- Release Date：2018/08/22 16:28
Connecting operation panel to enclosure

To connect the operation panel to the enclosure, use the parameter unit connection cable FR-CB201, FR-CB203, or FR-CB205. The maximum cable length is 5 m. No... More Details >>
- No：21542
- Release Date：2018/08/22 16:28

61-70 of Total 85

Inquiries

page top