The 75K or higher DC reactor is included in the 75K or higher inverter. The option cannot be purchased separately.

Since the initial value of Pr.13 (Starting frequency) is 0.5 Hz, the operation does not start unless 0.5 Hz or higher fr

The station number and baud rate were set using the dial for the FR-A5NC, but parameter is used for the FR-A7NC. Pr.542

No, it is not changed. Pr.268 is the parameter for the operation panel.

There is no problem, however, earthing (grounding) from each FG terminal is recommended to avoid the influence of noises

The communication is established if DA, DB, and DG are connected each other.

The signal becomes 0 when the RES signal is turned ON.

When the communication error occurs, the input signal status is not retained, and all the bits turn OFF. When the commun

The monitor with the code H01 switches by changing Pr.37 and Pr.144.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1171-1180 of Total 1368

prev 118 / 137page next

DC reactor

The 75K or higher DC reactor is included in the 75K or higher inverter. The option cannot be purchased separately. More Details >>
- No：21252
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Frequency command

Since the initial value of Pr.13 (Starting frequency) is 0.5 Hz, the operation does not start unless 0.5 Hz or higher frequency is set. When 0.49 Hz is set i... More Details >>
- No：21251
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Replacement

The station number and baud rate were set using the dial for the FR-A5NC, but parameter is used for the FR-A7NC. Pr.542 (Communication station number (CC-Lin... More Details >>
- No：21248
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
FR-A7NC (E kit)

They are insulated. More Details >>
- No：21242
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Pr.268 (Monitor decimal digits selection) during CC-Link communication

No, it is not changed. Pr.268 is the parameter for the operation panel. More Details >>
- No：21241
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Earthing (grounding) of FR-A7NC (E kit)

There is no problem, however, earthing (grounding) from each FG terminal is recommended to avoid the influence of noises. More Details >>
- No：21240
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Wiring of CC-Link communication cable

The communication is established if DA, DB, and DG are connected each other. More Details >>
- No：21239
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Remote input signal of CC-Link communication

The signal becomes 0 when the RES signal is turned ON. More Details >>
- No：21238
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Remote input signal of CC-Link communication

When the communication error occurs, the input signal status is not retained, and all the bits turn OFF. When the communication establishes again, the bit tu... More Details >>
- No：21237
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Monitor code of CC-Link communication

The monitor with the code H01 switches by changing Pr.37 and Pr.144. More Details >>
- No：21236
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

1171-1180 of Total 1368

Inquiries

page top